Edge Products Accessory System EAS (expandable)
Edge accessory (EAS) was created with future expandability in mind. The
architecture of the EAS allows users to connect multiple accessories
daisy-chain style to the Evolution CS or CTS. This means Edge can create
optional accessories that can be added by the owner at any time. A
second exhaust gas temperature (EGT) probe is one example of an optional
accessory that will be offered by Edge.
My Style Software
Add up to 16
additional sensors with the EAS universal senor input. Then setup,
configure and customize those sensors through Edge’s My Style software
package. Then Edge My Style software will recognize and Universal Sensor
Input that has been connected to your CS or CTS and allow the user to
change PID name, gauge name description and units. The user can choose
from a number of preconfigured sensors or enter in a custom look-up
table to translate the input voltage to the measured parameter value and
The EGT probe is a
sensor that allows users to monitor critical Exhaust Gas Temperatures
to ensure added power is not creating excessive heat which, in turn can
can cause engine damage. With EAS system a user can connect multiple EGT
sensors to monitor temperatures in different locations and compare
readings to be even more precise.
A turbo timer is a
device designed to keep an engine running for a pre-specified period
of time or a until a specific temperature is reached in order to
automatically execute the cool-down period required to prevent premature
turbo wear and failure. This also allows the lubricating oil from the
engine to circulate properly so the turbine won’t burn the lubricating
oil that would otherwise be trapped within the charger with the turbine
rotating at a high speed.
EAS UNIVERSAL SENSOR INPUT
The EAS Universal
Senor Input provides the ability to read any 0-5 volt signal and
translate that signal a meaningful value for display on the Edge CS or
CTS. This means you can add custom temperature, pressure, Air/fuel and
even travel/position gauges to your Edge CS and CTS! Using the Edge
Accessory System provides the following benefits:
- Using My Style software, sensors can be easily configured and renamed.
- Up to 8
Universal Sensor Input will support up to 2 sensors for the vehicle.
Each Universal Sensor Input will support up to 2 sensors for a total of
16 additional sensors that can be added to your CS or CTS device.
Sensors from the manufactures other than Edge can also be attached to a
CS or CTS device through the EAS universal sensor input.
- Eliminates the necessity of routing multiple wires to the CS/ CTS monitor.
EAS PRESSURE SENSOR
Pressure Sensor is a 0 – 100 PSIg 1/8” NPT sensor that plugs directly
into the Universal Sensor Input system (p/n 98605). Edge’s Pressure
Sensor comes equipped with the proper wires and connectors to plug right
into the Universal Sensor Input system saving time and money on
cutting, splicing, and crimping wire terminals to connect the sensor.
Use Edge’s Pressure Sensor to monitor data such as Boost PSI, Fuel Rail
Pressure, Air Bag Pressure, Lift Pump Pressure, Pre and Post Intercooler
Pressure and many more.
Tolerance: +-1.5% Full Span over temperature range of -20C to 85C and +-2.4% Full Span over temperature range of -40C to 135C.
EAS TEMPERATURE SENSOR
Temperature Sensor is a –40F to 300F 1/8 NPT supplied with the
connectors to plug directly into Edge’s Universal Senor Input System.
Using Edge’s Temperature Sensor you can monitor Transmission Temp,
Differential/Axel Oil Temp, Oil Temp, Engine Coolant Temp, Air intake
temp, Pre and Post Intercooler Temp and many more. Use this in
conjunction with the Universal Sensor Input and the CS and CTS monitor
to allow you to view critical temperatures with the most state-of- the-
art product on the market today.
EAS AMBIENT TEMPERATURE SENSOR
If your vehicle
is not equipped with an outside temperature sensor then this is a must
have! The EAS Ambient Temperature Sensor is a –40F to 230 F Waterproof
0.2” diameter sensor ready to plug into Edge’s Universal Sensor Input
system. Now you’ll never wonder what outside temperature is again.
* – EAS Starter Kit Cable required
** – EAS Starter Kit Cable and EAS Universal Sensor Input required
The EAS Starter Kit Cable is required to connect a EAS system to any
CS or CTS device. Only one EAS starter kit Cable required per CS or CTS
The EAS Universal (5 volt) Sensor Input is also required to add any
sensor. One Universal Sensor Input can connect up to 2 different
- 000.00 lbs
Edge Products 98615 EAS 12V Power Supply Starter Kit
SCT 9616 Analog Input Cable
Edge Products 98617 EAS Competition Kit